Segadora comercial sin asiento W61R
- John Deere
- Segadoras sin asiento
Buscar sucursal más cercana
Buscar ubicación
Características y especificaciones
- Plataforma segadora flotante de 61 pulgadas (155 cm)
- Motor V-twin potente de 25 hp (18,6 kW)
- Sistema de transmisión hidrostática autopropulsada
- Controles fáciles de usar para la comodidad y practicidad del operador
- VELOCIDAD DE TRANSPORTE EN REVERSA 0-70,5 mph
- ARRANQUE Eléctricos
- Plataforma 61"
- HP* 25 hp (18,6 kW)
- + Expandir todo
- - Cerrar todo
-
V-twin engine delivers smooth operation and plenty of power
Electronic fuel injection (EFI) engine Air-cooled engine, left side
W61R Commercial Walk-Behind Mower has an electronic fuel injected (EFI) air-cooled, vertical-shaft engine.
- 25 hp (18,6 kW)
- 45,6 in³ (747 cc)
- Electric start with a large 300 cold-cranking amp (CCA) battery for fast, convenient starts
- EFI allows for fast starts without use of a choke - no choke lever is needed.
- Starts are quick and easy, even for inexperienced operators.
- El sistema EFI aumenta el tiempo productivo.
- Los arranques rápidos y confiables son habituales al igual que con un automóvil moderno. EFI automatically meters fuel, including the extra fuel needed to start a cold engine, eliminating flooding from unnecessarily choking a warm engine. No es necesario ajustar el carburador en altura.
- There are no choke-related problems since the choke is eliminated, thus ensuring operator confidence and quick starts, even in cold ambient temperatures (snow blower use). El cable del acelerador mecánico es reemplazado por una conexión eléctrica que no es propensa al desgaste o al congelamiento.
- Se reduce el costo de propiedad.
- El sistema EFI mide con precisión el combustible que va a cada cilindro del motor. Se espera que el consumo de combustible sea aproximadamente un 10 % menor que en un tractor similar con carburador.
- Maintenance expenses are reduced because of fewer complaints related to hard starting, vapor lock, misfire, run-on, or fouled spark plugs.
- V-twin design for smooth operation and fast starts
- Torsión uniforme y potente a velocidades bajas y altas
- Aluminum engine block
- Efectiva disipación del calor
- Fabricación liviana y resistente
- Diseño de válvula en culata
- Más caballos de fuerza y torsión por pulgada cúbica cubierta
- Mayor ahorro de combustible
- Menor consumo de aceite
- Temperatura de operación más baja
- Rotating grass chopper screen
- Filtro de aire de dos etapas para mayor vida útil del motor y funcionamiento eficiente
- Cylinder head cleanout ports to ease maintenance
- Hydraulic valve lifters
- Oil pressurized, ensuring that push rods stay in constant contact with the rocker arms
- No adjustment required
- Lubricación a presión total con filtro de bajo flujo
- Reduce el desgaste del motor, ya que garantiza la adecuada lubricación aún cuando se la usa en colinas o terreno desnivelado
- Ayuda a mantener limpio el aceite para aumentar la vida útil del motor
- Cumple con las normas estrictas de emisión de la Agencia de Protección Ambiental de EE. UU (EPA), sin pérdida de caballos de fuerza ni torsión
FUEL TANK AND BATTERY
Fuel tank and in-line fuel filter BateríaLarge, 5,4-gal. (20,4-L) top draw fuel tank is easy to fill with large filler opening in an easy-to-reach location.
- Fuel pump for dependable, consistent operation
- Top-draw system to reduce the chance for fuel leakage
- Replaceable in-line fuel filter for trouble-free operation
Powerful, 300-CCA battery is secured and protected from damage in an easy-to-access location.
- 25 hp (18,6 kW)
-
Serviceability features and a 2-year, bumper to bumper warranty maximize uptime
2-YEAR BUMPER-TO-BUMPER WARRANTY
John Deere warranty includes:
- Single source
- 24-month coverage
- Unlimited hours of use
- Commercial application
All parts, except tires and batteries (which are warranted under separate documents provided with each product), are warranted
ENGINE SERVICE
Engine service points, W48R engine shown Engine cleanout port covers and air filter removed, W61R shownEngine service points are easy to reach:
- Oil drain tubes are provided to reduce oil spills and mess.
- Cleanout ports make inspecting and cleaning engine cooling fins easy.
DURABLE AND ADJUSTABLE CONTROL LINKAGE
Control rods with adjustable ends Plated and adjustable control rods and endsControl rods and ends are plated to stop rust and corrosion:
- Large pivot points for minimal wear and long life
- Grease fittings to lubricate for continued smooth operation
- Adjustable rod ends for easy and accurate adjustments
Control linkages are positioned tightly to the main frame structure to protect them from damage, such as being bent that could impact the speed and tracking of the unit.
TRANSMISSION SERVICE
Transmission oil reservoir, W36M shown Replaceable transmission oil filter, W52R shownTransmission oil reservoirs are easy to access and fill.
The transmission oil filter is a replaceable spin-on type for easy service.TOW RELEASE
Transmission tow-release, M Series design Hydraulic bypass valve, R Series designTransmission tow valves are easy to find and use.
CONVENIENT TIE-DOWN LOCATIONS
Front tie-down points Rear tie-down points- Front and rear tie-down points are provided to aid in transport.
- More-rounded corners contribute to a clean, attractive appearance.
- Greater strength results from eliminating sharp angles where peak loads can cause failure.
-
Convenient controls for operator comfort and productivity
Operator station (R Series shown) Compact control console (R Series shown)
All of the controls are located within comfortable reach of the operator. Simplified operation of each control offers superior convenience, productivity, and safety:
- Color-coded and clearly marked levers, switches, and buttons enable simplified operation.
- Bilingual decals in English and Spanish are provided.
- The operator presence system requires that one of the bails must be depressed to operate the unit; the machine must be in neutral and the power take-off (PTO) must be disengaged to start.
- Operator presence control levers are recessed into control handle when engaged, provides a smooth contour and comfortable handle to hold during operation.
- Separate choke and throttle – This takes the guesswork out of choke operation, with less chance of fowling the spark plugs.
- The W61R model with electronic fuel injection (EFI) does not require a choke.
- Electric PTO clutch on the engine powers the mower deck. The PTO switch on the dash is easy to see and use.
- Speed and steering controls are designed for ease of operation.
- Ergonomically designed control configuration on all units gives good operator comfort and leverage while driving.
- A speed-control lever is conveniently located in the center of the console and used to set maximum desired speed.
- Low actuation force is required for operator comfort.
- The neutral lock is spring-loaded for easy release.
A convenient and easy-to-operate switch is located on the console to operate the electric clutch, which powers the mower deck.
PARKING BRAKE (W36M, W48M)
Parking brake lever, W48M shownW36M and W48M parking brake control lever:
- Color coded and located above the console, within easy reach of the operator
- Actuates internal braking mechanism of the transmissions
PARKING BRAKE (W36R, W48R, W52R, W61R)
Left brake pawl and color-coded parking brake control Right brake pawl, W48R shownW36R, W48R, W52R, and W61R parking brake control lever:
- Color coded and located above the console, within easy reach of the operator
- Actuates arm that creates a mechanical locking interference on both drive tires
- Brake pawl located near top of tire to eliminate contact with curbs
-
Optional mulching attachment for extra convenience
Optional mulching kit and blades (similar design shown)
An optional mulching attachment and special mulching blades are available:
- The high-performance mulching attachment includes formed steel baffles to control the material for superior performance.
- Special mulching blades can also be used when side discharging, though overall cutting performance may be slightly less than with the standard blades.
- The mulching attachment allows for conversion of the mower deck so it can be used to perform the mulching function (grass or leaves).
OPERATING TIPS WHEN MULCHING:
- Mow when grass is dry.
- Observe the one-third rule.
- No more than one-third of the grass blade should be cut off at one time. This allows more efficient mulching and will promote the continued good health of the grass.
- If the desired cut height cannot be achieved by cutting off one-third, or there is clumping of the clippings, it may be required to cut higher, wait a day, then lower the mower and make a second pass.
- Mow at proper intervals, approximately every four to five days.
- Always mow with sharp blades.
- Adjust ground speed to allow the mower deck to process the clippings effectively.
-
A fabricated floating mower deck delivers high-quality cut
W61R mower deck W61R mower deck
Las segadoras comerciales de John Deere siempre han demostrado calidad, rendimiento y durabilidad. Each commercial walk-behind mower is equipped with a high-quality fabricated mower deck:
- 10-gauge, 0,14-in. (3,42-mm) fabricated steel deck top with added 10-gauge, 0,14-in. (3,42-mm) spindle mounting plate
- 7-gauge, 0,19-in. (4,8-mm) side skirts with reinforcement bar
The fabricated, floating mower deck delivers an extremely high-quality cut in diverse conditions:
- Floating suspension enables the best possible cut.
- Reinforced front lower edge provides strength and durability.
- Four mower front wheels are double-captured for durability and adjustable to three positions to suit the cut height.
- Two-coat paint covering protects the mower deck and resists corrosion.
- Deep-deck design for superior capacity.
- Side and center anti-scalp wheels promote a smooth mowing job.
- Hardened steel blades extend cutting time and increase durability.
- High blade-tip speed of approximately 18.000 fpm (5.486 m/min) for more blade strikes per inch mowed.
- R Series mower decks include a rear wheel for additional anti-scalp protection.
- Adjustable to three height positions to suit the cut height
A high-quality polyethylene deflector gives an excellent finished appearance:
- Wide, formed discharge deflector provides even clipping distribution.
- Large discharge deflector evenly disperses expelled clippings.
Las ruedas de pivote con neumáticos que no se desinflan contribuyen a un corte liso y uniforme:
- Las ruedas de pivote grandes que no se desinflan permiten que la segadora se deslice suavemente sobre el césped.
- Caster wheels are close to the mower deck to reduce vehicle footprint and turning radius.
- With the wheels less exposed, there is less chance they will get snagged by immovable obstacles, thus improving maneuverability and reducing chance of damage.
MOWER CUT-HEIGHT ADJUSTMENT
Mower cut-height adjustments Mower cut-height adjustment clipA floating mower deck has several advantages over a fixed mower deck design:
- Follows ground contour more effectively for a more even cut
- Travels smoothly above the ground with minimal chance of scalping
- Easier to adjust the cutting height
Mower cutting height can be set from 1,5 in. (3,8 cm) to 4,5 in. (11,4 cm) in 0,5-in. (1,3-cm) increments:
- The free-floating deck gives a smoother, more level cut.
- Height-of-cut changes can be made without tools.
- Large handles are provided to facilitate lifting the mower deck for setting the cut height.
- Cut-height adjustment pins have 90-degree bend for easy removal and reinstallation.
Mower deck shields are easily removed with hand knobs for access to the drive belt and other service points:
- Easy-attach belt shields allow for quick access for service.
- Four hand knobs allow removal of both mower shields.
- Greaseable spindles with easy, top access for simplified servicing.
- Spindle grease fittings can be greased with shields in place.
OPTIONAL MULCHING ATTACHMENT
Optional mulching kit and blades (similar design shown)An optional mulching attachment and special mulching blades are available:
- The high-performance mulching attachment includes formed steel baffles to control the material for superior performance.
- Special mulching blades can also be used for side discharging, though overall cutting performance may be slightly less than with the standard blades.
Frenos
Tipo | Dynamic braking with hand controls, hand lever to set parking brake |
Dimensiones
Altura | 44,8 in. 114 cm |
Ancho | Deflector down - 75 in. 191 cm Deflector up for storage - 65 in. 165 cm |
Peso | 745 lb 338 kg |
Longitud con plataforma | 83 in. 211 cm |
Transmisión mecánica
Transmisión | Two Hydro-Gear, 0,73-cu in. (10-cc) hydraulic pumps and Danfoss 12 cu-in. (197-cc) wheel motors and ergonomic handles with spring loaded neutral lock |
Caja de cambio | Ergonomic handles with spring-loaded neutral lock |
Motores de rueda | Danfoss 12 cu in. 197 cc |
Sistema eléctrico
Arranque | Eléctrico |
Horómetro | Estándar, digital |
Sistema de arranque maniobrado por el operador | PTO off, park brake engaged, speed lever in neutral |
Motor
Filtro de aceite | estándar |
Control | Regulador de todas las velocidades con mecanismo Flyweight |
Silenciador | Bajo tono |
Sistema de enfriamiento | Refrigerado por aire |
Lubricación | Presión total |
Velocidad de funcionamiento | 3.600 rpm |
Fabricante/modelo | ECV740-EFI - California Air Resources Board (CARB) compliant |
Potencia | At 3600 rpm 25 hp* 18,6 kW |
Cilindros | V-twin |
Filtro de aire | Dual HD canister |
Válvulas | Válvulas en cabeza |
Arranque/Inicio | Electrónico/arranque eléctrico |
Desplazamiento | 45,6 cu in. 747 cc |
Horómetro | Estándar, digital |
Sistema de combustible
Interruptor del tanque de combustible/válvula de corte | No |
Sistema de suministro de combustible | Closed-loop electronic fuel injection (EFI) |
Toma del combustible | Toma superior |
Tipo de combustible | Gasolina |
Capacidad del tanque de combustible | 5,4 U.S. gal. 20,4 L |
Bomba de combustible | Vacuum-operated diaphragm |
Especificaciones clave
Tamaño de la segadora | 61 in. 155 cm |
Ruedas de tracción | 18 x 8,5-8 |
Ruedas de pivote | 9x3,5-4 semi-pneumatic |
Capacidad del tanque de combustible | 5,4 U.S. gal. 20,4 L |
Rango de velocidad | Forward, 0-7,5 mph 0-12,1 km/h Reverse, 0-3 mph 0-4,8 km/h |
Garantía | 24 meses, comercial, única |
Transmisión | Two Hydro-Gear™, 0,73-cu in. (10-cc) hydraulic pumps and Danfoss 12 cu-in. (197-cc) wheel motors and ergonomic handles with spring loaded neutral lock |
Potencia del motor | At 3600 rpm 25 hp* 18,6 kW |
Velocidad de la punta de la cuchilla | Approximately 18.000 fpm 5.486 m/min |
Fabricante/modelo del motor | ECV740-EFI - California Air Resources Board (CARB) compliant |
Neumáticos
Ruedas de pivote | 9x3,5-4 semi-pneumatic |
Ruedas de tracción | 18 x 8,5-8 |
Velocidad de desplazamiento
Velocidades de avance | Ilimitadas |
Velocidades de retroceso | Ilimitadas |
Rango de velocidad | Forward, 0-7,5 mph 0-12,1 km/h Reverse, 0-3 mph 0-4,8 km/h |
5
Great first year
Used it this past mow season and it operated flawlessly. Went with the 61" deck to get the efi engine. Very smooth cut even if the grass is overgrown.
AJay
- Desde: Masa
- Frecuencia de uso: Semanal
- Nivel de experiencia: Intermedio